Customer Reviews

Reviews 101 to 125 of 153
Page of 7
Used this for installing recessed LEDs in a new Hardie Board (concrete composite) soffit. Use a slow speed, don't try to hurry it by applying too much pressure, it cuts quite well as it is. It helps to "rock" the blade slightly around the perimeter as you cut, and ease up when you feel it start to break through... and WEAR A MASK! This makes a lot of silica dust when cutting through concrete.

Or better yet, if you cut a lot of holes to cut buy the Hole Pro Shield kit to collect the dust. That's what I ended up doing.
I bought this as a gift to my son who built a new home and had lots of holes to put into sheetrock. He has thanked me over and over for how great this is. Easy and extremely accurate, this saw will be well within1/10 of an inch of the desired diameter in drywall all day long. Great tool
Cuts perfectly round, clean holes for speaker installation.

Installed a full JL Audio system on a Mako 18LTS. 2x 6.5", 2x 10" subs & 2x wakeboard 7.7" cans. This tool made it so easy to install.
Great product! We work with large size and thick-walled HDPE and PVC piping. The problem with using conventional bi-metal hole saws to make taps into the plastic pipes was it would melt the plastic and gum up the hole saw teeth and make it very difficult to remove the plastic cut-out coupon from the hole saw. You had to make the tap at a very, very low rpm to not create heat and melt the plastic which was time and money. The Blue Boar Plumbers hole saws have tungsten carbide chisel teeth which cut and remove the cuttings quickly and easily without creating heat and melting the plastic. We'll be ordering another two sets for our other crews.
These replaceable tungsten carbide blades make cutting holes in plaster super easy, plus I drilled 10 holes and was good to go. The blades were still sharp, but I was prepared, I had an extra set in the carry case when they need to be replaced.
These replaceable tungsten carbide blades make cutting holes in plaster super easy, plus I drilled 10 holes and was good to go. The blades were still sharp, but I was prepared, I had an extra set in the carry case when they need to be replaced.
Drills quickly and cleanly through wood and stays sharper than the hole saws with teeth. The tungsten carbide teeth outlast dozens of high speed steel or carbide edge hole saws and we can use cordless drills on jobs and no need for stud drills and a generator
Drills quickly and cleanly through wood and stays sharper than the hole saws with teeth. The tungsten carbide teeth outlast dozens of high speed steel or carbide edge hole saws and we can use cordless drills on jobs and no need for stud drills and a generator
Works well with an 18v DeWalt 3-speed drill that has enough torque for even 6 inch Mega hole cutters. I have drilled 2 1/2 inches through alabaster and ipe boards. This hole saw cuts a lot better than high speed steel hole cutters that I have used in the past.
Great product! Can't say enough about the company. Excellent customer service and helpful staff. It's really nice to be able to cut a perfect hole in drywall above your head without getting a speck of dust in your eye! I would highly recommend this to anyone.
Blue Boar worked great for making holes to install 6" LED recessed lighting in a plaster ceiling. Made installation easy. Lights fit inside the holes like a glove. Remember, this boar is built for cutting into plaster and sheetrock. If you need a boar for wood, look for the other type of boar specifically made for cutting into wood materials.
It is clear that they use quality materials in these hole saws and quite a bit of metal goes into these. The sidewall is twice as thick as a typical hole saw it seems. The teeth are large and welded above the deep gullets, giving the saw incredible ripping ability even at low operator pressure. I think the Blue Boar also represents a good value to a remodeler or contractor, especially when compared to similar sizes in home improvement stores that have less metal, perform worse, wear faster and don't last.

Gabrial Gabrial about 4-3/8" Carbide Grit Hole Saw Cutter Verified Purchase

I purchased this after ruining a cheaper one. I used this to install a dozen recessed lights in plaster ceilings. do not use to cut the wood lathe but it will cut through the old plaster without dulling. Still works well after many uses.
This thing cuts about 5 times faster than bi-metal hole saws!
The Blue Boar hole saw is awesome. I used a battery powered drill (Makita 18 volt) as recommended and have drilled a few dozen holes in I-joists for HVAC. The board that was drilled falls out of the saw most of the time instead of having to pry it out. The hole is quickly cut.!
the cutting through many inches of wood was quick and with little difficulty. a really good tool. used a lot but still as sharp as day I got it
the cutting through many inches of wood was quick and with little difficulty. a really good tool. used a lot but stii as sharp as day I got it
This is THE best hole cutter I have used. Cutting through 1" ply and even 1" ply with some pine backing was super-easy and super fast. The saw really does churn out the cuttings as you work - just as advertised. Also, getting the cut-outs cleaned out for the saw is easy and fast.
I was even cutting holes easily with my wimpy 14.4V Panasonic cordless - I tried it for the heck of it, and it cut through 8-9 holes easily for a recent project.
This is THE best hole cutter I have used. Cutting through 1" ply and even 1" ply with some pine backing was super-easy and super fast. The saw really does churn out the cuttings as you work - just as advertised. Also, getting the cut-outs cleaned out for the saw is easy and fast.
I was even cutting holes easily with my wimpy 14.4V Panasonic cordless - I tried it for the heck of it, and it cut through 8-9 holes easily for a recent project.
Very fast cutting hole saws and top performance with my 18 volt cordless drills. I no longer need my large angle drill or extension cords with these cutters.
Long life even with MDF and particle board materials like Advantech or plywood where bi-metal dull very quickly. I use them even on Hardi board.
Very fast cutting hole saws and top performance with my 18 volt cordless drills. I no longer need my large angle drill or extension cords with these cutters.

Long life even with MDF and particle board materials like Advantech or plywood where bi-metal dull very quickly. I use them even
on Hardi board.’.
I have been using this product for over 3 years now. Great performance in wood. goes like hot knife through the butter! Good on wood! Lasts a long time
I ve been using this products for over 3 years now. Great performance in wood: goes like hot nife through the butter! Good on wood! Lasts a long time
These hole saws cut through hardibacker like butter! Highly recommend!
These hole saws cut through hardibacker like butter! Highly recommend!
Page of 7